Equipment

Clip for horizontal lifting of concrete and natural stone, with automatic locking and unlocking of the load

• Automatic latch: Release the load automatically resting on the ground
• Possibility of connecting lifting eye to hook grubby
• rubber pads

Opening range: 280-1050mm

• Adjustable Width

Maximum Load Capacity: 1500kg

• Wide clamping range

Disc sander Ø180mm very versatile with speed regulation.

• Constant electronics and adjustable speed dial: Unbeatable sanding work
• Soft Aranque: Makes the job easier for the operator
• Low center of gravity: Optimum handling due to shorter distance between shaft and polishing plate
• Safety cable: More durable and flexible
• Power: 900 W
• RPM: 2500-4700
• Screw thread: M14

Makita Grinder A 1400W with vibration reduction system.

• Longer lasting gears and head
• Narrow body with safer grip and comfortable
• spring absorbs vibrations. Relieves the blow with disc engaged
• . Duration of brushes: +40%
• button Robust locking
• Soft start: prevents high voltage spikes
• current limiting
• variable speed when overloads are present

Makita Grinder of 2200W with anti-restart system, to prevent its start-up with the lock-on activated after a power cut.

• New head format: more robust and durable
• Protection against loss of grease and dust: with torca seal on the head, shaft and armature
• Non-slip grip: More control and comfort
• Large switch
• More powerful and durable motor

Lightweight drill with high stability on vertical and horizontal surfaces: Cement, stone, glass, metal.

Vacuum based for instant installation without anchors or clamps.

• You can replace the portable magnetic hole that is only used on iron materials
• Surfaces: Flat smooth or rough
• Vacuum base: Exceptional stability
• Maximum free speed: 1500rpm

Máquina para realizar las ranuras en forma de T que sujetan el fregadero, evitando así el encolado y procesos largo de preparación. También se usa en paredes verticales ya que la función de doble ventosa facilita la sujeción de manera estable y continua.

CARACTERÍSTICAS

• Enganche rápido para agua
• Enganche rápido para aire: 2 zonas separadas, permitiendo trabajar en los bordes.
• Utilizada para cortar ranuras T para la colocación de pernos de anclaje en encimeras, frontales, sistemas arquitectónicos.
• Vastago de 6mm.
• 30.000rpm.
• 750w.
• Conectores ¼”

Kit consisting of two fixation systems that automatically maintain the pressure on the miter.

Includes:

• 2 Miter scents with suction cups 12.7 cm gray
• 2 suction cup covers
• Generated 10-port venturi
• 10 air connectors
• 50 cm of tuberia
• Industrial quick-connect male coupler
• Carry case

Tool to reduce traditional method settings

Pneumatic cutter with water and air hoses without folds: Better use and reduced operator fatigue.

• 2HP enginewith cruise control
• Easy miter cutting : 3 cm material 
• Cutting holes sinks and sinks,slots and rods
• Duty cycle: 2000 hours
• Includes cutting disc Ø150/thickness 2.1 mm
• Allows dry and wet use

PRODUCT APPROVED BY:

Table storage rack, glass plates, worktops or material debris.

• Tough/light material
• can be assembled one by another to increase its capacity
• positioning bars according to need

Dimensions:

• Bars: 180cm x 6.0 cm
• Rail: 152cm x 28cm x 14cm
• Rubber stop at end of each bar
• withstands up to 1360 kg per spacer
• Rack Weight: 118 kg
• up to 2700kg

Type "A" folding stand for storage of boards, worktops and material residues.

Rugged, lightweight aluminum construction:

• Withstands up to 5,400kg on each side: Total 11,800kg

Folding base legs:

• They facilitate mobility and storage when not in
• Rubber stops

Open dimensions:

• Base: 152 x 152cm
• Height: 147cm
• Weight: 34.5kg

Manufacturing stand designed for use in the workshop or workplace.

Adjustable height:

• Ability to adjust working height from 91 to 106 cm

Strong and light material:

• Weight 17.2 kg

Rubber top:

• Anti-slip and rubber base marks

Resistance in kg:

• Weight supported:226 kg folded /136 kg extended

Transport trolley for boards, glass plates, worktops and material residues, up to 1,800 Kg.

• Strong/lightweight material
• Rubber bars and base in height and length: Prevents slipping/scratches
• Side eyes: lifting with truck/torus
• Rubber feet and bars

Weight supported: 1,800kg/ Weight: 336kg

Approved Cart: CE CERTIFIED

Glass Harp Rack for workshop transportations.

• Harp Rack includes 60 long and short plastic covered rods that allow for easy and protected sliding of glass in and out of the rack. There are 80 possible hole locations for rods.
• Gray powder coated finish.
• Recommended for use in shops and warehouses.

Mobile work stand for worktop manufacturing.

Placing full kitchens joining several tables along or at 90° angles:

• Two integrated end clamps for table union
• Safety locks on legs for immobilizing
• strong castors Ø20 cm

Rubber-coated:

• Top: Prevents sliding and side marking
• : table joining

Two heavy-duty slings for boards up to 2 meters

consisting of two layers and with full length pads:

• Sewn inside the body for extra protection against very strong wear

:

• Resistance up to 7,390 Kg

Dimensions:

• 7.6 cm W x 259 cm L
• Weight: 13.6 kg

Large sling bar

• very useful for table transport

allows you to position slings at the appropriate distance for safe travel:

• Removable pins on top of the beams, holding slings in place

Resistance:

• Up to 4,500 kg

Supports slings up to 10 cm

• Bar weight: 90 kg

Lifting with crane or fork lift truck

Powerful vacuum cleaner with blower function: Mortar, brick powder, chalk, ceramic, plaster.

• Accessory AREAS
• Personal tools area
• Connection possibility Flexible tube to air outlet
• Maximum connectable power: 2600W
• Reservoir 30L: Stainless steel
• Automatic mode
• Filtration Special dirt
• "PET" filter High strength
• cleaning system "Push&Clean"
• wheels
• Air inlet regulating adapter

Motorized single block cutter with fixed bridge, equipped witha stressed and chrome-plated active bridge that guarantees a greatrobustness and precisionof cutting.

Very robust and suitable for cutting high thicknesses and hard materials.

• Side grips:Extend the working plane by facilitating the movement of the
• Side stop device :Facilitates parallel cutting

Robust and compact cutterwiththe essentialsof MAS cutters small and also with an improved loom.

• Possibility of mounting a roller tablefor better movementlarge boards
• Developed according to customer needs

Rotating machinefor angle cuts on stone panels.

Simplifiescutting into small parts, tiles and design parts

• Available with manual head movement(+45° to -45° with precision positioner) or motorized
• Maximum precision cutting: special design of the bridge
• Vertical/transverse forward of the unit manually
• Maximum width of parts: 600mm head 0°/400mm head 45°